Auto Rust Technicians

SafeTCap ART-142-S is designed to be direct replacements for the original rear upper coil spring mounts on your Jeep TJ and LJ. The spring plate and the frame mount bracket are made from 11 gage cold rolled steel. There is a pre welded 2.5″ long bump stop mount tube included with an m10-1.5 weld nut. The attached frame mount bracket is made to slip over the frame after removing the old spring mount. Learn More

Our SafeTCap ART-146 is a complete replacement for the original track bar and upper trailing arm bracket mounted on the rear axle. This mount was developed to fit a 2.75 diameter axle, but will work on larger diameter axles. The bracket straddles the sway bar bracket which remains in place during installation. The ART-146 is welded directly to the axle once the old bracket is removed and the surface to be welded is prepared. Our ART-146 bracket is made from 7 gage steel, and is CNC cut, bent,... Read More Learn More

Our ART-143 rear lower coil spring mount for the 1997-2006 Jeep Wrangler TJ/LJ was designed as a direct replacement for your original coil spring mount on the rear axle. This part is to be welded on the rear axle once the original spring mount is removed and the axle is ground down to clean metal. Our ART-143 is made from 7 gage steel and is CNC cut, bent and assembled by our AWS certified welders in the USA. This part is sold individually and is designed to fit both Driver and Passenger... Read More Learn More

Our SafeTCap ART-136 is a replacement for the OEM rear track bar bracket on the Jeep Wrangler TJ. The bracket is made from 7 gauge HRPO steel, CNC cut, bent and MIG welded in the USA facility. The hardware to remount the track bar is included with the bracket. To install this part you will need to disconnect the track bar and you simply cut off the old mount and weld the new mount in the footprint of the old mount. ATTENTION: The SafeTCap ART-136 is designed as an OEM replacement and is not... Read More Learn More

Our Safe-T-Cap frame repair kit is designed for a severely rusted frame on the TJ Wrangler. We have found that the frame starts to rust from the inside out, and can create an unsafe condition. Learn More

Our ART-124LJ frame repair kit is designed to slip over your stock frame, while maintaining factory dimensions and mounting points. Learn More

Our SafeTCap® ART-135-1-R Front Frame Section was designed to cap over the passenger side original frame after removing the rotted metal, then welding the new frame repair section to the frame. Learn More

Wranglers have weld-nuts inside the frame rails that secure the transfer case skid plate in place. The skid plate also is the transmission and transfer case mount. Typically the bolts are a problem to remove due to rust on the inside of the frame rail. When this happens, access holes are often cut unto the side to facilitate removal of these bolts. This method gives access to dirt and water, which can collect inside the rails and rust them from the inside out. This Safe-T-CapTM kit is a... Read More Learn More

Rear Upper Trailing Arm Mount Replacement, Left (Driver) Side. Fits 1997-2006 Jeep Wrangler TJ. Our replacement mount is made from Heavy Duty 7 Gauge Steel, CNC Cut and Welded by our Certified Welders! The original factory mount is made from thinner material, making it susceptible to rusting out and tearing away from the frame. The part includes a new high grade bolt and nut welded in place. Learn More

This kit is designed to repair the front frame section where the leaf spring perch is mounted. This is behind the front axle. The front kit is ART-102. The frame in this area seems to trap a lot of dirt, road debris, and mud, as well as water is able to get inside the boxed frame. Once its trapped it starts to rust from the inside out, and can fail before you even know you have a problem. Our repair kit is manufactured from precision CNC cut sections of heavy guage steel, and includes a new... Read More Learn More