Suspension - Control Arms

Synergy MFG Heavy Duty Fixed Front Lower Control Arms For 2007+ Jeep Wrangler JK 2 Door & Unlimited 4 Door Models Abrasion resistant powder coat finish for maximum durability and corrosion resistance Made from high quality crush resistant 1 3/4" x.188 wall 1026 DOM tubing Arms are bent up and in for additional ground and tire clearance Arms are 1/4" longer than stock and deliver stock caster (5.0 degrees) on a 3" lifted vehicle Features Synergy Dual Durometer Bushings (DDB) with Teflon®... Read More Learn More

Replace or repair your used FlexArm bushings and sleeves. This kit is designed to repair one arm. Bushings are made from polyurethane, and sleeves are steel. Details: Lower FlexArm Includes Bushings and Sleeves Each Learn More

TJ Rear Axle Upper FlexArm Mount- Passenger Details: FlexArm Mount Passenger Side Rear Upper Learn More

Replacment upper control arms. Details: FlexArm Front Upper Learn More

The angled rod end forging is designed for applications needing additional clearance for tires, or other frame configurations. The Flex joint ends provide excellent off-road capabilities with articulation and durability. They dampen road noise and vibration. The forging uses standard 1-1/4” x 12 tpi. with a 9/16” center bolt. 10 degree angle off joint. Used on our JK Lower Control Arms for better Tire clearance in tight turns. Shoulder width= 2-5/8” Bolt dia.= 9/16” [14mm] Shank angle =... Read More Learn More

The TeraFlex FlexArm joint rebuild kit includes all required replacement components to rebuild a TeraFlex FlexArm joint. Depending on vehicle driving condtions, grit, grime, dust and fluids all take their toll on the tolerances of the bushings. To keep the joint functioning correctly it is necessary to rebuild the joint periodically and restore the joint to top working condition. This kit includes a chrome plated misalignment ball, two urethane bushings, large retainer washer, and snap ring. Learn More

The medium spherical urethane Monster end uses the same internals as its larger brother, in a scaled down version. The end utilizes a 7/8” x 18 tpi. shank and accepts a 7/16” bolt. Details: Right hand thread 2" shoulder width 7/8" x 18 TPI shank Accepts 7/16" bolt Shoulder Width = 2" Bolt Diameter = 12mm 7/8-18 UNS thread 1 1/4" wrench on jam nut Learn More

Lower Long FlexArm Single For 1997-06 Jeep Wrangler TJ & TJ Unlimited Models Clevite Bushing Zerk Hardware The TeraFlex TJ lower long FlexArm can be added to any existing TeraFlex long arm suspension lift. FlexArms allow custom pinion and caster angles to be set for proper alignment, they also are used to re-center the axle in the wheel well for proper suspension movement, and to adjust wheelbase length. This kit includes one adjustable TJ lower long FlexArm. Learn More

Rear Upper Sport FlexArm Kit For 2007+ Jeep Wrangler JK 2 Door & Unlimited 4 Door Models With 2.5" - 3" Lift Premium black e-dipped coating Pre-adjusted length arms correct caster and pinion angle 1-5/8" x 0.156 wall DOM tubing Sold as a pair TeraFlex sport fixed-length flexarms are designed to offer maintenance free performance for 2.5" - 3" lift. Pre-adjusted length arm corrects caster and pinion angle for 2.5" - 3" lift kits. 1-5/8" x 0.156 wall DOM tube stands up to trail abuse and... Read More Learn More

Features Fully-adjustable Alpine Flexarm control arms that give precise and commanding driving position with attention to pinion & caster angles. The heavy-duty Control arms will correct sag and sway for a proper suspension alignment. They require zero maintenance, and are easy to install. Sold as a set of (8) and carry a limited lifetime warranty. Learn More